Roller Conveyor line is a common continuous conveying equipment, because of its obvious advantages, so that it can not only connect the production process, but also directly involved in the production process, so in the electronic, electrical, pharmaceutical, chemical, hardware, food, beverage, textile, building materials industry and all kinds of logistics transportation, especially in various processing, assembly, packaging, storage and other pipeline has been widely used. Roller Conveyor Roller Conveyor,Flexible Roller Conveyor,Industrial Roller Conveyor,Roller Belt Conveyor Shandong Sinolion Machinery Corp. Ltd , https://www.packingline.nl
1, plate factors
At present, the ps version used in the printing industry is mostly based on aluminum plates, and a certain amount of zinc is added. In addition to having a certain tensile strength, it also has a certain degree of ductility. Under certain conditions, the tensile strength of the new PS version is stronger than that of the new PS version. With the printing version made with the new PS version, the ductility is not obvious. If a plate made of recycled PS is used, especially in the case of a large number of impressions, this change can be clearly felt. With the increase of the number of prints, the entire printing plate extends from the middle along the two directions of the fixed printing plate, and the more the number of printings of the printing plate changes, the more obvious the printing plate becomes. Do not add backing paper to the back of the plate to maintain printing. If necessary, the plate must be discarded to ensure quality.
The main cause of this quality problem: After the electrolysis of the PS version, although no qualitative changes have occurred, the surface of the sand is significantly coarser than the new PS version, and the thickness and weight are also reduced. The thickness of the new PS version is 0.3mm, and the thickness of the PS version after electrolysis is sometimes less than 0.15mm, and its tensile strength is naturally not as strong as the new PS version, but the ductility is stronger than that of the new PS version. When the operator loads the plate, it will pull the edge of the plate directly because it is too hard when tightened. The new ps version weighs 0.5kg per piece, while most of the recycled ps versions do not reach this weight, and some are even lower than 0.25kg. The plate thus produced has poor tensile strength, and sometimes the whole plate can be elongated. More than 5mm, its scalability is naturally stronger than the PS version. Since most offset presses work at high speeds, the plates will be deformed and the prints on the plates will be deformed.
2, blanket factors
The effect of the blanket on the distortion of the printed writing, the author believes that there are mainly the following factors:
Reason 1: The purchase of unqualified rubber blankets cannot reach the normal service life, lose its proper performance, and result in imprinting deformation during printing.
Solution: Replace the qualified blanket immediately.
Cause 2: The blanket is not installed properly, and loosening occurs halfway.
Solution: Reinstall the blanket.
Reason 3: Due to the operator's failure to clean the surface of the blanket in time (such as ink, etc.), a long time, the surface area of ​​the blanket has a thick layer of impurities, the surface hardening, can not be cleaned, absorbed during the printing process The moisture on the surface of the printing plate expands and the surface of the printing plate is deformed.
Solution: Clean up in time and replace the blanket when it cannot be cleaned.
Roller conveyor is applicable to all types of boxes, bags, trays and other pieces of cargo transport, bulk materials, small items or irregular items need to be placed in the tray or container for conveying. Can transport single piece weight of a large material, or bear a larger impact load, easy connection between the roller line filter, can be used more than one drum line and other transport equipment or special plane to form a complex logistics system, to complete various process needs. Can be used to achieve the accumulation of material stacking conveyor. Roller conveyor is simple in structure, high in reliability, easy to use and maintenance.
The phenomenon of imprinting deformation and its processing technology
In the printing process, the phenomenon of imprinting deformation is commonplace. Based on past practical experience, various factors that cause imprinting deformation in the printing process are summarized below for reference by peers.